Calibration Checklist

CALIBRATION CHECKLIST Created by ChecklistGuro (https://checklistguro.com) --- EQUIPMENT IDENTIFICATION & INFORMATION --- [ ] Equipment Name/Description [ ] Manufacturer [ ] Model Number [ ] Serial Number [ ] Asset Tag Number [ ] Date of Last Calibration [ ] Next Calibration Due Date [ ] Location (Production Line 1, Production Line 2, Quality Control, Warehouse, Other) [ ] Any previous issues or notes? --- ENVIRONMENTAL CONDITIONS --- [ ] Ambient Temperature (°C) [ ] Ambient Temperature (°F) [ ] Relative Humidity (%) [ ] Air Pressure (kPa) [ ] Date of Environmental Measurement [ ] Time of Environmental Measurement [ ] Notes on Environmental Conditions (e.g., drafts, unusual fluctuations) --- CALIBRATION STANDARDS --- [ ] Standard Serial Number [ ] Standard Uncertainty (k=2) [ ] Standard Traceability (e.g., NIST, ISO) (NIST, ISO, Other (Specify)) [ ] Traceability Details (Specify originating standard) [ ] Standard Calibration Due Date [ ] Standard Calibration Certificate [ ] Standard Condition (As Received) (Within Tolerance, Out of Tolerance, Unknown) --- PRELIMINARY CHECKS & WARM-UP --- [ ] Equipment Serial Number [ ] Visual Inspection Notes (damage, cleanliness, etc.) [ ] Power Supply Condition (Nominal, Low, High, Unstable) [ ] Warm-up Time (minutes) [ ] Warm-up Start Time [ ] Initial Readings / Baseline Measurements (before full calibration) [ ] Equipment Stability Check - Pass/Fail (Pass, Fail) --- CALIBRATION PROCEDURE --- [ ] Procedure Step 1: Initial Setting & Zeroing [ ] Span Adjustment Value (if applicable) [ ] Zero Adjustment Value (if applicable) [ ] Calibration Method Used (e.g., Relative, Absolute) (Relative, Absolute, Other (Specify)) [ ] Notes on Procedure Execution (e.g., any deviations from standard) [ ] Number of Readings Taken [ ] Calibration Points Used (0% Span, 25% Span, 50% Span, 75% Span, 100% Span, Other (Specify)) [ ] Attach Calibration Graph (if applicable) --- DATA ACQUISITION & RECORDING --- [ ] Measurement 1 Reading [ ] Measurement 2 Reading [ ] Measurement 3 Reading [ ] Ambient Temperature (°C) [ ] Ambient Humidity (%) [ ] Date of Measurement [ ] Time of Measurement [ ] Notes/Observations During Measurement [ ] Measurement Unit (mm, cm, m, inch) --- TOLERANCE EVALUATION --- [ ] Measured Value 1 [ ] Tolerance Upper Limit (Value 1) [ ] Tolerance Lower Limit (Value 1) [ ] Result of Value 1 (Within Tolerance?) (Yes, No, Not Applicable) [ ] Explanation/Comments (if Value 1 is out of tolerance) [ ] Measured Value 2 [ ] Result of Value 2 (Within Tolerance?) (Yes, No, Not Applicable) [ ] Explanation/Comments (if Value 2 is out of tolerance) --- ADJUSTMENT & CORRECTION (IF REQUIRED) --- [ ] Detailed Description of Adjustment(s) Performed [ ] Adjustment Value 1 (e.g., Offset) [ ] Adjustment Value 2 (e.g., Gain) [ ] Adjustment Method Used (e.g., Software, Manual) (Software Adjustment, Manual Adjustment, Other (Specify)) [ ] If 'Other' selected above, please specify the adjustment method. [ ] Number of Adjustment Cycles [ ] Confirmation of Adjustment Stability (Stable after 1 cycle, Stable after 2 cycles, Stable after 3+ cycles, Unstable - Further investigation required) [ ] Date of Adjustment [ ] Time of Adjustment [ ] Technician Signature (Adjustment Confirmation) --- FINAL VERIFICATION --- [ ] Span Value (Post-Adjustment) [ ] Zero Value (Post-Adjustment) [ ] Linearity Error (Max) [ ] Repeatability Error (Max) [ ] Pass/Fail Result (Pass, Fail) [ ] Comments / Observations (If Applicable) [ ] Date of Final Verification [ ] Time of Final Verification [ ] Technician Signature --- CALIBRATION CERTIFICATE & DOCUMENTATION --- [ ] Certificate Number [ ] Calibration Date [ ] Next Calibration Due Date [ ] Equipment Name [ ] Equipment Model [ ] Equipment Serial Number [ ] Calibration Results Summary [ ] Calibration Data Files [ ] Calibration Technician Signature --- EQUIPMENT RETURN & TAGGING --- [ ] Return Location [ ] Equipment Tag Number (Pre-Calibration) [ ] Equipment Tag Number (Post-Calibration) [ ] Return Date [ ] Return Time [ ] Condition Upon Return (Clean, Slightly Dirty, Dirty, Damaged) [ ] Notes on Return/Condition [ ] Technician Signature --- END OF TEMPLATE --- Transform this text into a digital, automated, and trackable mobile app! Visit: https://checklistguro.com/templates/facility-management/calibration-checklist (Click "Install Template" to launch your digital inspection tool immediately)